The article in the next paragraphs relating to How to Install a Bathtub Yourself is indeed enlightening. Read it yourself and decide what you think about it.
Mounting a bath tub isn't exactly rocket science, yet it does need solid plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately hard job. If the old bathtub is easily accessible, the project can relocate rapidly; if you need to open a wall surface to remove the old tub as well as position the brand-new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to move out the old tub and set in the new one. Make sure you have qualified yourself for the task and fit attempting it. Instead of hiring a service provider to take control of a halfway-completed task, it is much better to consider utilizing one before you begin. Opportunities are you might need a specialist plumber to make tube links.
This post will help you install a new tub in your restroom if you have actually currently gotten a new bathtub and don't require to alter the plan of your previous water supply pipes.
Your devices and material list must consist of the following:
Getting ready for the Installation
To start with, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its last setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you must do is detach the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of removing the existing faucets can be fairly problematic as a result of the restricted gain access to that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have been gotten rid of, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Prior to carrying on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Installing the Tub
Using both wood boards under its feet, position the tub in the needed position. The wood boards are useful in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level and also adjusting the feet on the bathtub till the level reviews degree.
To install taps, fit all-time low of the outermost adaptable faucet port to the ideal supply pipe by making a compression join; then do the exact same for the other faucet.
Turn on the water and also inspect all joints and new pipework for leakages and also tighten them if needed. Fill up the tub and likewise check the overflow outlet and the normal electrical outlet for leakages.
Lastly, deal with the bathroom paneling as described in the producer's user's manual. Tiling as well as sealing around the bathtub must wait up until the bath tub has been used at least once as this will certainly resolve it right into its last position.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and also the sink. Safeguard the faucet in position with the manufacturer supplied backnut. When the faucet is securely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous kind must be attached to the faucet ends first, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to split an inflexible seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, resulting in issues with wetness as well as possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes as well as cartridges, as well as are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the tub with water prior to securing, to allow for the movement experienced when the bathtub is in use. The sealer can crack rather early if you do not take into consideration this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is advisable to fit the tiles using water-resistant or water-proof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been guided to that report on Installing A Bathtub from a friend on a different web blog. Sharing is caring. You never know, you may just be doing someone a favor. Thank-you for taking the time to read it.
Search no more; expert plumbers.